Cypress is a large city, and the electrical work that comes out of it reflects that. A single block can hold a newer construction home with a modern 200-amp panel, a property from the eighties running on original wiring, and a commercial unit with a tenant buildout mid-way through. Ranes Electric handles all of it. The job type changes with the property, and the approach changes with the job.
What stays the same is the process. A licensed electrician shows up, assesses what is actually there, and works from that. For a homeowner dealing with a tripping breaker, that means tracing the fault through the circuit. For a property manager coordinating access across multiple units, that means fitting the work around what the building allows. The call starts the same way either way: tell us what is happening, and we will tell you what comes next.
Cypress has a housing stock that spans several decades of construction, and the electrical systems inside those homes reflect that span. A house built in the last ten years is likely to have arc-fault protection, a panel sized for modern loads, and grounding throughout. A house from the seventies or eighties may have a panel that was adequate then and is not now, two-prong outlets in rooms that have never been updated, and wiring that has been added to in pieces without a consistent plan.
The homes and wiring in this area have their own quirks, and that is what makes a proper assessment matter. We look at what is actually in the walls and at the panel before recommending anything. If a targeted repair is the right call, that is what we say. If the system has been patched enough times that a more thorough approach makes more sense, we say that too. Either way, wiring work is checked against code before sign-off.
Properties built in the last decade tend to come with larger panels and code-compliant wiring throughout. The calls from these homes are usually about additions: a dedicated circuit for a home office, an EV charger circuit in the garage, a ceiling fan in a room that was pre-wired but never finished. The infrastructure is there. The work is adding to it cleanly.
Properties that have been renovated over time can be harder to read. Updates to the kitchen or bathrooms may have added GFCI protection where it was needed, but the panel behind it all may still be running on original equipment. We look at the full picture, not just the part that prompted the call.
Flat and apartment electrical work has its own shape. The panel for an individual unit is often in a utility closet, a hallway, or a shared electrical room rather than in the space itself. When a breaker trips or an outlet stops working, the first question is whether the fault is inside the unit or somewhere in the building's shared supply.
We handle the work on the tenant side of the meter. If a problem traces back to the building's main distribution or to equipment that sits outside the unit, that is a conversation for the building manager or the utility. We will tell you exactly where the line falls. For landlords and property managers coordinating repairs across units, we can work around occupancy and access schedules. Qualified electricians for every job, whether it is a single outlet in one unit or a panel assessment across a whole floor.
Same-day appointments are often available in Cypress. When you call, we ask about the situation and confirm whether it can be handled that day or whether a scheduled visit makes more sense. For problems that will not keep, we treat them accordingly.
For businesses and rental properties that need to stay operational, we work around what the space requires. A commercial tenant that cannot shut down a section of the floor gets a different approach than an empty unit being turned over between tenants. We confirm the plan before work begins so the timing and access details are clear. We show up ready to work.
The price for any electrical job depends on what the job actually involves. An outlet replacement is a different scope than a panel upgrade. A single ceiling fan installation is a different scope than running new wiring through a finished wall. When you call, we ask enough questions to give you a rate that reflects the real scope, and we confirm what that covers before anything is scheduled.
If we get on site and find something that changes the picture, we tell you before continuing. You are not handed a different number at the end. The price is confirmed upfront, and what it includes is explained. Ask what it covers and you will get a straight answer. Call (936) 241-9792 to get started.
Outlets and switches are the most visible part of a home's electrical system, and they are also where small problems tend to show up first. An outlet that has stopped working, a switch that controls nothing, or a GFCI that trips immediately after reset all point to something specific. We trace the fault, replace what needs replacing, and confirm the circuit is working correctly before we leave. For new installations, we confirm the circuit can carry the added load before running anything new.
A detached garage or workshop that needs more than a single circuit benefits from its own subpanel fed from the main. That gives the space dedicated capacity without overloading the circuits that serve the house. We size the subpanel for what the space actually needs, run the feeder from the main panel, and confirm grounding and bonding are correct throughout.
When a home's service entrance is no longer adequate for what the property is running, a service upgrade is the right answer. This involves replacing the panel, upgrading the meter and service-entrance equipment, and confirming the new service is sized correctly for the home's actual load. It is the kind of job that comes up in Cypress when a household adds significant new load: an EV charger, a large addition, or equipment that the existing service cannot support.
Battery-operated alarms are a starting point, but hardwired alarms with battery backup are more reliable and are required by code in new construction and in many remodels. We install interconnected hardwired alarms so that when one sounds, they all sound. For properties being brought up to current standards, we assess what is there and install what is needed.
A generator that is not wired through a transfer switch is a hazard to utility workers and to the generator itself. The transfer switch isolates the home from the grid when the generator is running, which is what makes the system safe to operate. We handle the transfer switch installation, the wiring between the generator connection and the panel, and the grounding and bonding that the installation requires. We stand behind every circuit we touch.
Smart switches and dimmers are straightforward installations in most cases, but they depend on having the right wiring behind the wall. Older homes sometimes lack a neutral wire at the switch box, which some smart switch models require. We confirm what is there before recommending a specific device, and we handle the installation and configuration so the switch works correctly from the start.
Not every electrical call starts with a clear picture of what is wrong. Sometimes the symptom is obvious and the cause is not. That is where the diagnostic work matters.
A dead outlet, a breaker that will not stay reset, or lights that flicker under load are all symptoms. The cause might be a loose connection, a failing breaker, an overloaded circuit, or something in the wiring path between the panel and the device. We work through each possibility in order and confirm the fix before closing anything up. The service page carries the full breakdown of what a diagnostic visit covers.
A panel that cannot keep up with the home's load shows up in predictable ways: breakers that trip under normal use, lights that dim when something large starts, and no room to add circuits without removing others. When those signs appear together, a panel assessment is the right starting point. We look at what the panel is carrying, what it was designed for, and what would be needed to bring it in line with current demand.
Adding a circuit, installing a ceiling fan, running a dedicated line for an EV charger, or wiring a new room all require the same thing: a clear understanding of what the existing system can support and what needs to change to support it. We assess the panel and the relevant circuits before any new work is run. Code-compliant wiring throughout, and the work is confirmed before sign-off.
We cover Cypress and the surrounding communities in Harris County. If you are in Jersey Village, Tomball, or Stagecoach, we handle calls there too. The same process applies: call, describe the situation, get a rate, and schedule if it makes sense.
We are accountable to the community we work in. That means being clear about what the job involves, confirming the price before work starts, and doing the work correctly the first time.
There is more on the electrical services page.
Meter and service entrance work involves the utility company as well as the electrical contractor. We handle the wiring and panel side of the job and coordinate with the utility on the parts that require their involvement. We explain what that process looks like before the work is scheduled.
Permit requirements in Harris County depend on the type and scope of the work. Larger jobs such as panel replacements and service upgrades typically require a permit and inspection. We confirm what applies to your specific job before anything is scheduled, and we handle the coordination on our end so it does not fall on you.
It depends on the condition of the wiring, whether it was installed to code, and whether it is rated for the intended use. We inspect existing outdoor wiring before incorporating it into new work. If it does not meet current standards or is deteriorated, we say so and explain what replacing it involves.
The work area is cleaned up before we leave. Any debris from the job, wire clippings, packaging, and similar material, is removed. If access points were made in walls for wiring, those are left ready for patching, which is a separate finishing trade.
Start by isolating whether the fault is inside one unit or affecting shared circuits or the building's main distribution. Call us and describe what you are seeing across the units. We can assess the scope over the phone, confirm whether a single visit can address the problem, and work around tenant access and occupancy to minimize disruption.
Some outdoor work can continue in light rain with proper precautions, but certain tasks, particularly open trench work, conduit runs, or work near the service entrance, are safer to schedule around weather. We confirm the plan before the visit and adjust if conditions make it unsafe to proceed.
The call is still the right starting point, because we need to ask follow-up questions that a photo alone cannot answer. That said, if you have photos ready when you call, walk us through what you are seeing and we can factor that into the conversation.
Equipment on a circuit that is being de-energized needs to be shut down before we cut power to that circuit. We confirm the shutdown plan in advance so you have time to save work and close out anything that cannot handle an abrupt loss of power.
Either works. Tenants can call (936) 241-9792 directly to describe the fault. If the property is managed, we confirm the authorization and billing arrangement before scheduling, so the right person is in the loop before work begins.
We run a dedicated circuit from the main panel to the structure, which involves trenching for underground conduit or running overhead cable depending on the property layout. The circuit is sized for whatever the shed needs to power, and grounding and bonding at the outbuilding are part of the installation.
Not necessarily. Whether a commercial space needs to close depends on which circuits are being de-energized and for how long. We assess the scope before scheduling and work with the business to plan around operating hours where that is possible.
Call Ranes Electric at (936) 241-9792 and tell us what is happening. We will ask about the property, the situation, and what you have already noticed. By the time the call is done, you will have a rate, a clear picture of what the visit covers, and a schedule that works for you.
Schedule it. We wire it. You're powered.
Nearby towns we cover: Tomball, Pinehurst, Magnolia, The Woodlands.
Everywhere else we go is in our service area list.
Every electrical job is different, and the right fix depends on what is actually happening in your system. The table below covers the services we handle most often in Cypress and Harris County, what each one involves, and a practical note to help you decide where to start. Call (936) 241-9792 for a quote on any of them before anything is scheduled.
| Service Type | Scope of Work | Common Situations | What to Keep in Mind |
|---|---|---|---|
| Whole-Home Surge Protection | panel-level surge device installationprotection for every outlet and circuitlightning and utility-switching coveragesingle installation, whole-house coverage | Homes with modern electronics, smart appliances, or frequent storm exposure | Southeast Texas sees significant lightning activity. Panel-level protection catches a spike at the service entrance before it reaches any device in the house. |
| Outlet & Switch Installation | standard and GFCI outlet replacementdimmer and standard switch installationoutdoor weatherproof outletsgarage and exterior locations | Homeowners upgrading outlets or replacing failed devices | A GFCI outlet installed incorrectly may not trip when it should. Proper installation matters as much as the device itself. |
| Electrical Safety Inspections | pre-purchase and pre-sale inspectionsGFCI and AFCI protection reviewpanel and grounding assessmentcode violation documentation | Buyers, sellers, landlords, and lenders requiring documentation | An inspection before closing on an older Cypress property gives you a clear picture of what the system looks like before you own the problem. |
| Electrical Repairs & Troubleshooting | dead outlets and partial power losstracing faults to the sourcearc-fault and ground-fault diagnosisGFCI and AFCI device testing | Any home or business with an unexplained electrical problem | A proper diagnosis starts at the panel and works outward. Guessing and replacing parts at random costs more in the long run. |
| Electrical Panel & Service UpgradesMost Popular | 200-amp service upgradespanel replacement and breaker upgradesload calculation before sizingsubpanel installation | Homes with tripping breakers, dimming lights, or no room to add circuits | Many Cypress homes were built with 100-amp service. Modern loads from central AC, electric ranges, and EV chargers can push that service to its limit. |
| Older-Home Rewiring | whole-home rewiringaluminum wiring assessmenttwo-prong outlet groundingknob-and-tube evaluation | Older Harris County properties with outdated or inconsistent wiring | Aluminum branch wiring and ungrounded two-prong outlets are not automatic emergencies, but all of them deserve a clear-eyed look from a qualified electrician. |
| Wiring & Circuit Installation | new circuit runsgrounding and bonding workwiring for additions and remodelscode-compliant tie-in to existing system | Additions, remodels, or any space that needs new wiring | Wiring work is checked against code before sign-off. If the panel cannot carry the added load, we say so before work begins. |
| EV Charger Installation | dedicated 240-volt circuitpanel capacity assessmentoutlet or hardwired charger connectiongarage and exterior runs | Electric vehicle owners adding a Level 2 charger at home | If the panel needs room added before the charger can go in, we handle that as part of the same project so there is one clear scope and one call. |
| Lighting Installation | recessed and surface-mounted fixturespendant and chandelier wiringsecurity and landscape lightingunder-cabinet lighting | Homeowners remodeling or adding exterior lighting for safety | Outdoor lighting in Cypress sees year-round use. A weatherproof fixture installed correctly the first time avoids callbacks. |
| Breaker & Fuse Repair | breaker replacementtripping breaker diagnosisfuse panel assessmentload testing | Properties where a breaker trips repeatedly or will not reset | A breaker that trips immediately under load tells us something different than one that trips after extended use. Both get resolved, but the path is different. |
| Dedicated Appliance Circuits | refrigerator and dishwasher circuitsmicrowave and range circuitsworkshop and garage equipmentcircuit sizing for the specific load | Appliances that share a circuit and cause repeated tripping | A shared circuit that trips under normal appliance use is a sizing problem, not just a nuisance. A dedicated circuit fixes it at the source. |
| Ceiling Fan Installation | new installations where no wiring existsreplacement of older fansswitch leg wiringbox and brace support | Homeowners adding fans in bedrooms, living rooms, or covered patios | If no wiring exists at the location, we run the circuit and the switch leg as part of the same visit. |
| Backup Generator Installation | transfer switch installationdedicated wiring to the panelgrounding and bondingutility line isolation confirmation | Properties in areas with storm-related outages or extended grid stress | The transfer switch is what keeps the generator isolated from the utility line. Correct installation protects both the equipment and utility workers restoring power. |
Call (936) 241-9792 to talk through any job on this list and get a quote before anything is scheduled.
(936) 241-9792